Search found 9 matches
- Thu Jan 12, 2017 8:04 am
- Forum: DCC Forum
- Topic: Any idea what this is????
- Replies: 8
- Views: 1663
Re: Any idea what this is????
Well I fitted the Hornby chip and it still didn't work, so I removed it and wired directly to the motor and it still didn't work. In the end I took a meter and checked that the voltage on the rails reached the motor, it didn't. After a bit of poking around I worked out that the motor was fitted the ...
- Tue Jan 10, 2017 3:51 pm
- Forum: DCC Forum
- Topic: Any idea what this is????
- Replies: 8
- Views: 1663
Re: Any idea what this is????
Thanks for getting back. It seems the Select should work with the Bachmann 36-553 but I did google a few people where it had been set to a higher address than the Select can handle. In that case nothing will happen unless someone with an Elite or other more sophisticated controller resets it. The ea...
- Sat Jan 07, 2017 7:43 pm
- Forum: DCC Forum
- Topic: Any idea what this is????
- Replies: 8
- Views: 1663
Re: Any idea what this is????
Don't worry after a bit of googling I now realise there are probably a 100 decoders.
- Sat Jan 07, 2017 7:04 pm
- Forum: DCC Forum
- Topic: Any idea what this is????
- Replies: 8
- Views: 1663
Re: Any idea what this is????
Here's the pic, I think.
Yea got there in the end.
Yea got there in the end.
- Sat Jan 07, 2017 7:01 pm
- Forum: DCC Forum
- Topic: Any idea what this is????
- Replies: 8
- Views: 1663
Any idea what this is????
Hello clever people, I just got a Lima Class 33 with DCC chip in it. Any idea what it is????
And any idea if it should work with a Hornby Select??
Many thanks
Richard
And any idea if it should work with a Hornby Select??
Many thanks
Richard
- Sat Nov 05, 2016 8:12 pm
- Forum: Dapol
- Topic: Dapol wheels
- Replies: 20
- Views: 5609
Re: Dapol wheels
Rather than drill out the centre axle boxes as suggested by Bufferstop you could always do the "Final" engineering solution. That is remove all traces of flanges off the centre wheel set, dare I say simple enough. Having done that it becomes in effect a 4 wheel wagon and all B2B settings ...
- Fri Nov 04, 2016 10:24 pm
- Forum: Dapol
- Topic: Dapol wheels
- Replies: 20
- Views: 5609
Re: Dapol wheels
Oh, How to change them. I use the thumb on one hand to spring the axle box out while the thumb and forefinger hold and pull the axle alongside the axle box you're springing out. Be warned though 6 wheel milk tankers are prone to problems and some experimenting needed before you crack it. Geoff T. I...
- Fri Nov 04, 2016 10:04 pm
- Forum: Dapol
- Topic: Dapol wheels
- Replies: 20
- Views: 5609
Re: Dapol wheels
The Dapol axle is a different length to the Hornby and Bachmann one . As to whether you could swop the wheels , I havent checked if they were the same axle diameter or not.. Check the back to backs , because the shallow flanges leave them easier to derail than the Hornby deep ones, and make sure th...
- Fri Nov 04, 2016 8:47 pm
- Forum: Dapol
- Topic: Dapol wheels
- Replies: 20
- Views: 5609
Dapol wheels
Hello, I'm new to this having been bought a Hornby Tornado set, it played on my mind 'til I made a 6x4 table then it played on my mind 'til I bought a Somerset Belle set. So far so good. Then I went to a local model rail exhibition and among other things I got a DAPOL milk tanker. It just derails al...