Search found 820 matches

by RFS
Mon Apr 05, 2021 11:34 am
Forum: DCC Forum
Topic: LENZ digital set 01, what's it worth
Replies: 3
Views: 126

Re: LENZ digital set 01, what's it worth

The LZ100 and LV100 are very old - the version 3 manual on the Lenz web-site is dated September 2000. Both were replaced by the combined LZV100 which has itself been replaced by the LZV200. You therefore might struggle with these two. But the LH100 handset and the TR150 power supply have value and i...
by RFS
Thu Mar 11, 2021 6:24 pm
Forum: DCC Forum
Topic: Nce power cab booster and circuit breaker breaker
Replies: 5
Views: 219

Re: Nce power cab booster and circuit breaker breaker

If you are using any form of frog polarity switching, then it's important to also isolate the frog by cutting the link wires from the blades underneath. Otherwise the frog is still receiving power via the blades, and when the DCC80 switches power you can get a DCC short if the blades haven't moved o...
by RFS
Tue Feb 23, 2021 9:24 am
Forum: DCC Forum
Topic: Z21 and Detectors - Question
Replies: 1
Views: 111

Re: Z21 and Detectors - Question

The software you mention is iTrain rather than iTrack, and I would suggest you would be best joining the iTrain forum and asking this type of question there where there are people familiar with these products. As with Freiwald Traincontroller, which I use, you can configure automation with only a si...
by RFS
Fri Jan 29, 2021 6:40 pm
Forum: Electrical & Electronics
Topic: Very odd running behaviour from a new EMU
Replies: 14
Views: 388

Re: Very odd running behaviour from a new EMU

But don't solder the track joints! In hot weather the rails won't be able to expand, and will instead be prone to buckling. I would suggest adding some more feeds. The problem could be the conductive couplings, and perhaps there's one that's causing a momentary short circuit as the couplings flex ro...
by RFS
Fri Jan 29, 2021 2:57 pm
Forum: Electrical & Electronics
Topic: Very odd running behaviour from a new EMU
Replies: 14
Views: 388

Re: Very odd running behaviour from a new EMU

Which Bachmann EMU is it? I have several and not experienced any problem.
by RFS
Fri Jan 01, 2021 7:43 pm
Forum: Electrical & Electronics
Topic: Electrifying a hinged section
Replies: 5
Views: 342

Re: Electrifying a hinged section

My Lenz LZV100 command station has a facility to connect up emergency stop switches by wiring them across the E and M terminals. For the lift-up flap I have fitted a push-to-break push-button switch (same type as fitted to fridges to turn the interior light off when you close the door). So lifting t...
by RFS
Thu Dec 31, 2020 5:46 pm
Forum: Track/Layout Design
Topic: DCC Power Drain
Replies: 6
Views: 378

Re: DCC Power Drain

Supplying 4A of power to a layout of this size via a single feed is likely to cause serious problems. What you are seeing by "reduced power" is voltage drop at locations furthest from the feed. The risk is that when you get a short at these locations due to voltage drop, the Select does no...
by RFS
Sat Dec 26, 2020 4:06 pm
Forum: DCC Forum
Topic: bachmann
Replies: 6
Views: 325

Re: bachmann

I would also recommend you check your DCC wiring is up to managing a 5-amp load. Easy way is to do the coin test - ie use a coin/piece of wire to trigger DCC shorts at various places in the track and make sure the DCC command station trips out immediately. If it doesn't then you may need to beef up ...
by RFS
Mon Dec 07, 2020 9:51 pm
Forum: DCC Forum
Topic: Hornby Locos noisy when slow running on DCC control
Replies: 9
Views: 562

Re: Hornby Locos noisy when slow running on DCC control

The Zimo MX600R would be an ideal replacement for the R8249. I would suggest investing in one and see what difference it makes.
by RFS
Sun Dec 06, 2020 3:47 pm
Forum: DCC Forum
Topic: Double Header
Replies: 5
Views: 326

Re: Double Header

If your layout has a double-track section, it can be useful to place the locos side-by-side there so that you can see how they run when in a double header, and make small adjustments to CVs until they are properly speed-matched.
by RFS
Sat Nov 28, 2020 3:34 pm
Forum: Bachmann
Topic: N Class front coupling question
Replies: 2
Views: 156

Re: N Class front coupling question

Pretty certain it's just screw-fitted to the front pony truck. You will have to remove the truck to get at the screw to do this.
by RFS
Sat Nov 21, 2020 9:45 pm
Forum: Bachmann
Topic: Birdcage question
Replies: 8
Views: 302

Re: Birdcage question

If you are using automation, and want to fit resistors for track circuiting, then doing that on these coaches is a doddle.
by RFS
Sun Nov 08, 2020 5:19 pm
Forum: DCC Forum
Topic: DCC Short
Replies: 16
Views: 622

Re: DCC Short

These older motors are quite power-hungry. The Hornby R8249 decoder is only rated at 0.5A and has no short circuit or overload protection. I would recommend a better decoder such as the Lenz Standard+ that is rated at a full 1A and also has short circuit protection. An alternative would be the Zimo ...
by RFS
Fri Oct 23, 2020 8:33 pm
Forum: General Model Railway Discussion / News
Topic: Peco Y points Electrofrog
Replies: 5
Views: 377

Re: Peco Y points Electrofrog

The topic has been covered a few times on another forum (RMWeb), eg https://www.rmweb.co.uk/community/index.php?/topic/157365-peco-small-y-electrofrog-normal-y-point/&tab=comments#comment-4084991 This topic also contains links to some other threads on the topic too. Basically you have to modify ...
by RFS
Sun Sep 20, 2020 8:53 pm
Forum: General Model Railway Discussion / News
Topic: More eBay nonsense...........
Replies: 96
Views: 9094

Re: More eBay nonsense...........

Well I am flabbergasted, you can buy this for about £24.99 - £ 29.99, just look at this price. https://www.ebay.co.uk/itm/Rare-Hornby-R8508-Skaledale-Hubbards-Hill-Mill/254488943357?hash=item3b40b91afd:g:qHkAAOSwk09eJ3kX I suspect most of these £1000 items are just placeholders - he doesn't actuall...

Go to advanced search